| Donate $25 for two DVDs of the Cryptome collection of files from June 1996 to the present |
|
9 September 2008. A Zipped PDF of the full original NSTISSAM TEMPEST/1-92:
http://cryptome.org/nstissam1-92.zip (14.5MB)
31 October 1999
Source: Hardcopy from the National Security Agency received October 21, 1999.
Released in response to an FOIA
request dated May 18, 1998. Of twenty-two TEMPEST-related documents
requested, only parts of two were released. NSA
wrote that most remain classified as SECRET and unreleasable. An
appeal for additional releases has been filed.
This a fifth and final part of transcription of a 172-page document in which classified sections, about half of the volume, have been redacted (indicated by xxxxxxxx).
First part of transcription, Appendix A: http://cryptome.org/nstissam1-92a.htm
Second part, Table of Contents and Sections 1-5: http://cryptome.org/nt1-92-1-5.htm
Third part, Sections 6-12: http://cryptome.org/nt1-92-6-12.htm
Fourth part, Distribution List: http://cryptome.org/nt1-92-dist.htm
The other release, NSA/CSS Regulation 90-6, Technical Security Program, a 12-page document: http://cryptome.org/nsa-reg90-6.htm
Classification symbols: (U) = unclassified, (C) = classified, FOUO = for official use only. Overstrikes in the original.
For comprehensive TEMPEST stuff (non-secret, that is) see The Complete, Unofficial TEMPEST Information Page: http://www.eskimo.com/~joelm/tempest.html
From Table of Contents
APPENDICES
A. CLASSIFICATION OF COMPROMISING EMANATIONS INFORMATION (Separate file)
A.1 GeneralA.2 Scope
A.3 Rationale
A.4 Classification Marking
A.5 Foreign Release
A.6 Specific Guidelines
A.7 TEMPEST Classification Chart Outline
A.8 TEMPEST Classification Chart
B. DESCRIPTION OF CORRELATED SIGNALS
C. TEST GUIDELINES FOR PARALLEL INFORMATION TRANSFER EQUIPMENT
C.1 PurposeC.2 Parallel Transfer Example
C.3 Types of Parallel Information Transfer
C.3.1 Return-to-Zero Signals
C.3.2 Nonreturn-to-Zero Signals
C.3.3 Polygraphic and Multiplexed SignalsC.4 Test Patterns
C.4.1 Type A Test Patterns
C.4.2 Type B Test Patterns
C.4.3 Type C Test PatternsC.5 Emanation Measurement Procedures
C.6 Evaluation of Results
C.6.1 Bit Density
C.6.2 The Effect of Parity Check BitsC.7 Effect of Multiple Signals
D.1 ScopeD.2 Introduction
D.3 Examples of Scanning and Character Generation Methods
D.3.1 Scanning
D.3.2 Character GenerationD.4 Examples of Defining Rd
D.4.1 Standard TV Display -- Continuous Scan
D.4.2 Dot Matrix -- Continuous Scan
D.4.3 Dot Matrix -- Modified Continuous Scan
D.4.4 Stroke or Vector GenerationD.5 Special Test Requirements
D.5.1 Alphanumeric CRT Displays
D.5.2 Bit Mapped Displays
E. AUTOMATED TESTING SYSTEMS CERTIFICATION REQUIREMENTS
E.1 PurposeE.1.2 [sic] Supplementary Manual Test
E.1.3 General Approach
E.1.4 System Certification Philosophy
E.1.5 Alternative ApproachesE.2 Automated Test Procedures
E.2.1 General
E.2.2 Tuning Scheme
E.2.3 Measurement Accuracy
E.2.4 Digital Voltmeter
E.2.5 Measurement Gate Time
E.2.6 Substitution SourcesE.3 Advance Certification Testing Requirements
E.3.1 Rd-Type Signal Certification Tests
E.3.2 Rd-Type Signal Certification TestsE.4 Periodic Calibration Verification Requirements
E.4.1 Internal Attentuator Calibration Verification
E.4.2 Internal Source VerificationE.5 Scan Accuracy Verification Requirement
E.6 Automated Detection Systems Using A Spectrum Analyzer
E.6.1 Implementation
E.6.2 Automated Testing Procedures Using A Spectrum Analyzer
E.6.3 Advance Certification Testing Requirements
E.6.4 Rt-Type Signal Certification TestsE.7 Critical Feature List Requirements
E.7.1 Critical Features ListE.8 Documentation Requirements
E.8.1 Test Instrument Certification
E.8.2 Test Plan Additions
E.8.3 Data Collection and ReportingE.9 Security
F. DETECTION SYSTEM BANDWIDTH MEASUREMENT
F.1 IntroductionF.2 6 dB Bandwidth Measurements: Tunable Heterodyne Detection System With Demodulator
F.2.1 Signal Generator Requirements
F.2.2 Measurement ProcedureF.3 6 dB Bandwidth Measurements: Tunable Heterodyne or Tunable Non-Heterodyne Detection System Without Demodulator
F.4 6 dB Bandwidth Measurements: Non-tunable Detection Systems
F.5 Impulse Bandwidth Measurements (IBW): Tunable Heterodyne Detection System With Demodulator
F.6 Impulse Bandwidth. Measurements: Tunable Heterodyne or Tunable Non-Heterodyne Detection System Without Demodulator
F.7 Impulse Bandwidth Measurements: Non-tunable Detection Systems
K. IMPULSE GENERATOR CALIBRATION
Distribution List (Separate file)
[Pages B-1 to B-10]
CONFIDENTIAL
B.1. (U) The tester has the responsibility to describe clearly and accurately any correlated signals detected during TEMPEST testing. Table B-1 depicts the relationship between displayed emanations and types of correlation. This table is not meant to be all-inclusive. Figures B-1 through B-8 illustrate some examples of correlated emanations. The upper trace(s) is teh monitor signal (i.e., RED signal) and the bottom trace(s) is the detected signal. The photographs are representative of onlya few of the possilbe types of correlation. Also, the photographs depict a high signal-to-noise ratio to facilitate reproduction and to demonstrate easily recognizable correlation. Under certain test conditions, the correlation may be far less obvious and distinct.
Table B-1
ILLUSTRATION OF CORRELATED EMANATIONS (U)
[Table redacted.]
[Figure redacted.]
Figure B-1. -- Examples of Correlated Emanations. A-Scope Display
(U)
[Figure redacted.]
Figure B-2. -- Examples of Correlated Emanations. A-Scope Display
(U)
[Figure redacted.]
Figure B-3. -- Examples of Correlated Emanations. A-Scope Display
(U)
[Figure redacted.]
Figure B-4. -- Examples of Correlated Emanations. A-Scope Display
(U)
[Figure redacted.]
Figure B-5. -- Examples of Correlated Emanations. Raster Display
(U)
[Figure redacted.]
Figure B-6. -- Examples of Correlated Emanations. Raster Display
(U)
[Figure redacted.]
Figure B-7. -- Examples of Correlated Emanations. Raster Display
(U)
[Figure redacted.]
Figure B-8. -- Examples of Correlated Emanations. Raster Display
(U)
CONFIDENTIAL
[Pages C-1 to C-6]
CONFIDENTIAL
[Figure redacted.]
Figure C-1. -- Parallel Trasnfer of Data (U)
[Figure redacted.]
Figure C-2. -- Bit Density Emanation Examples (U)
[Ten lines redacted.]
___________________
1 NSTISSAM TEMPEST/2-91, "Compromising Emanations Analysis Handbook". [Footnote to unknown passage.]
[Figure redacted.]
Figure C-3. -- Fingerprint Emanation Examples (U)
[Ten lines redacted.]
[Two full pages redacted.]
[Page C-6] THIS PAGE INTENTIONALLY BLANK
CONFIDENTIAL
[Pages D-1 to D-10]
CONFIDENTIAL
D.1. (U) Scope. -- This appendix describes the operation of alphanumeric CRT displays and presents guidelines for determining RED signaling rates.
D.2. (U) Introduction.
[Twenty lines redacted.]
D.2.3 (U) The determination of Rt is made in the same manner as described in 5.5.2.
D.3. (U) Examples of Scanning and Character Generation Methods.
D.3.1 (U) Scanning.
D.3.1.1 (U) Video Scan: Continuous. -- In a continuous scan display, the electron beam of the CRT starts at a given coordinate point and sequentially moves through each coordinate point at a fixed sweep speed. This type of scanning can be extended to other types of CRTs, such as a standard TV monitor where the scanning is "interlaced" (see Figure D-1).D.3.1.2 (U) Video Scan: Modified Continuous. -- The electron beam of the CRT scans all the displayable points for each character of all character positions. The pattern traced by the defiection system is normally a vertical modulation of a herizontal sweep. This type of scan uses a sawtooth pattern sometimes referred to as a "diddle pulse" sawtooth pattern (see Figure D-2).
D.3.1.3 (U) Random Scan. -- In a CRT display with this type of scan, the beam is not scanned linearly, but is directed from any screen location to any other.
D.3.2 (U) Characrer Generation.
D.3.2.1 (U) Standard TV Display. -- The individual characters are displayed by unblanking the electron beam during line segments of a continuous scan (see Figure D-3).
D.3.2.2 (U) Dot Matrix. -- The individual characters are displayed by unblanking the electron beam at the appropriate positions in a dot matrix (see Figure D-4).
D.3.2.3 (U) Stroke or Vector Generation. -- The individual characters are displayed by "drawing" small line segments (vectors) to make up the character (see Figure D-5). The program which is controlling the display must control the electron beam position, as well as unblanking, since there is no raster.
D.3.2.4 (U) Beam Extrusion. -- The individual characters are displayed by passing the electron beam through a selected shaped aperture in a metal plate which causes the beam to assume the shape of the aperture when focused on the face of the CRO.
D.4. (U) Examples of Defining Rd.
[Fifty lines redacted.]
D.5 (U) Special Test Requirements.
D.5.1 (U) Alphanumeric CRT Displays.[Full page redacted.]
[Ten lines redacted of a, b, c and d.]
D.5.3 (U) The testing organization shall provide signalling characteristics used to determine the Rd's and Rt's. Any deviations to the above test requirements shall be documented and justified.
UNCLASSIFIED
[Pages E-1 to E-6]
UNCLASSIFIED
E.1 (U) Purpose. -- [Four lines redacted.]
E.1.1 (U) Supplementary Manual Test. -- [Six lines redacted.]E.1.2 (U) Alternative Approaches. -- [Three lines redacted.]
E.2. (U) Automated Test Procedures.
E.2.1 (U) General. -- [Twelve lines redacted.]E.2.2 (U) Prescan Calibration Procedures. -- [Four lines redacted.]
E.2.3 (U) Calibration Verification During Testing [Five lines redacted.]
E.3. (U) Automated Detection System Parameters.
[Twenty lines redacted.]
E.4. (U) Documentation Requirements. -- Documentation requirements for automated testing are indicated below and in Paragraphs 6.3 and 8.4.
[Thirty-two lines redacted.]
[Full page and five lines redacted.]
[Page E-6] THIS PAGE IS INTENTIONALLY BLANK
UNCLASSIFIED
[Pages F-1 to F-4]
UNCLASSIFIED
F.1. (U) Introduction. -- The overall detection system bandwidth shall be used when determining compliance of TEMPEST detection systems with the bandwidth requirements of this document. Procedures are presented for measuring sine wave and impulse bandwidths of non-tunable detection systems and tunable detection systems with and without a Demodulator. Alternate procedures rnay be used, provided the same results are obtained as when using the specified procedures herein. The alternate procedures used must be documented in the test instrumentation certification report and must be approved by the sponsoring organization.
F.2. (U) 6 dB Bandwidth Measurements: Tunable Heterodyne Detection System with Demodulator. -- This procedure is required for deterlIiining the overall 6 dB detection system bandwidth of tunable heterodyne detection systems at the post-detection output. This overall bandwidth is equal to the difference between the low-pass and high-pass 6 dB cutoff frequencies, as measured using F2.2.a through i below.
F.2.1 (U) Signal Generator Requirements. -- This procedure accounts for the effect of both the IF and video circuits upon the overall low-pass cutoff frequencies. An RF sine wave signal generator shall be used for the measurements. The RF signal generator carrier frequency shall be tunable and shall be within the tuned frequency range of the detection system. The RF generator carrier signal shall be amplitude-modulated with a sine wave using any convenient modulation index (e.g., 20 percent). The modulation index shall be maintained constant during the measurement, unless otherwise noted. The frequency of the modulating signal shall be adjustable over the modulating frequency capability of the RF signal generator. If the maximum usable modulating frequency is greater than the expected IF bandwidth, then only one RF signal generator is required. If the expected IF bandwidth is greater than the maximum usable modulating frequency, then two RF sine wave generators are required for the test. The second RF generator shall be tunable over the same frequency range as the first RF generator, but shall not be modulated. When two RF generators are required, both generators must provide frequency accuracy and resolution which are at least one order of magnitude better than the expected overall bandwidth.
F.2.2 (U) Measurement Procedure. -- The overall bandwidth shall be measured as follows:
a. (U) If one RF signal generator is required, apply the output of the generator directly to the input of the detection system. If two RF signal generators are required, apply both generators through a power divider to the input of the detection system. Inline attenuation (e.g., 20 dB) may be used as needed to provide signal attenuation and signal generator isolation. Initially, decrease the output of the second generator (if used) to zero or at least 40 dB below the output of the modulated RF generator.b. (U) Adjust the carrier frequency of the modulated RF generator around the tuned center frequency of the detection system until the maximum level of the modulating signal is observed at the same output port of the detection system as used during TEMPEST testing. The level of the modulated carrier signal applied to the detection system and the modulation index must be such that the detection system output signal is at or below the 1 dB compression Doint.
c. (U) Adjust the frequency of the modulating signal until the rnaximum output level of the detection system is observed or the maximum available modulating frequency has been reached, whichever comes first. Readjust the RF signal generator level, if necessary, to maintain the detection system output level at or below the 1 dB compression point. Note the modulating frequency and the detection system output level as a reference.
d. (U) Maintaining the same RF generator carrier frequency, as in c above, reduce the frequency of the modulating signal until the output of the detection system decreases 6 dB from the reference level noted in c above or until the modulating frequency is essentially zero frequency (such as would occur in d.c.coupled Demodulator), whichever comes first. Record this frequency as the 6 dB high-pass cutoff frequency.
e. (U) Increase the modulating frequency found in step d as necessary to produce a relatively noise free detection system output signal, but do not increase the modulating frequency to more than 10 percent of the overall bandwidth. Note the resulting modulating frequency and the detection system output level as a reference. Shift the RF carrier frequency down until the output of the detection system decreases 6 dB from the reference level of this step. Increase the RF generator carrier level by 6 dB and decrease the modulation index by 6 dB (e.g., to 15 percent).
f. (U) If only one RF signal generator is required, then increase the frequency of the modulating signal until the maximum output level of the detection system is observed. Note the new output reference level. Then, continue to increase the modulating frequency until the detection system output level decreases 6 dB from the new reference level. Record the resulting modulating frequency as the overall 6 dB low-pass frequency.
g. (U) If two RF signal generators are required, set the frequency of the second generator equal to the first generator, plus the reference modulating frequency of step e. Turn off the modulation of the first generator. Increase the level of the second generator until the detection system output equals the reference level of step c minus 6 dB. Next, increase the frequency of the second RF generator until the maximum output level of the detection system is observed. Note this output level as the new reference level. Then continue to increase the frequency of the second RF generator until the detection system output level decreases 6 dB from the new reference level. Record the resulting difference between the two RF generator frequencies as the overall 6 dB low-pass cutoff frequency.
h. (U) Subtract the result of d (above) from that of f or g (above) to obtain the overall 6 dB detection system bandwidth.
i. (U) Repeat the bandwidth measurements at a minimum of two tuned frequencies per decade or one near the center of each tuning band of the detection system, whichever is the greater number of readings.
F.3. (U) 6 dB Bandwidth Measurements: Tanable Heterodyne or Tunable Non-Heterodyne Detection System Without Demodulator. -- The bandwidth of these detection systems shall be mensured as follows:
a. (U) Apply the output of a calibrated unmodulated sine wave generator1 to the input of the detection system.b. (U) Adjust the carrier frequency of the cw generator around the center frequency of the detection systern until the maximum output level of the detection system is observed at the same port used during TEMPEST testing. Note the output level.
c. (U) Maintaining the same cw generator carrier amplitude and detection system tuned center frequency as in b (above), reduce the cw generator carrier frequency until the output level of the detection system decreases 6 dB from the level obtained in b (above), or until the carrier frequency is essentially zero frequency (such as would occur at a detection system output with d.c. response), whichever comes first. Note this frequency.
d. (U) Repeat c (above), except increase the carrier frequency until the output level decreases 6 dB from the level obtained in b (above). Note this frequency.
e. (U) Subtract the frequency recorded in c (above) from that in d (above) to obtain the detection system bandwidth.
f (U) Repeat the bandwidth measurements at a minimum of two frequencies per decade or one per tuning band (near the center), whichever is the greater number of readings.
___________________
1 A swept-frequency generator with a constant output voltage may be used in lieu of the manually-tuned generator. Using a calibrated display device, the detection system bandwidth can then be read directly.
F.4. (U) 6 dB Bandwidth Measurements: Non-Tunable Detection Systems. -- The 6 dB bandwidth on non-tunable detection systems shall be measured in accordance with the procedures specified in Paragraph F.3. The measurement shall be made on the entire composite detection system, including the transducer2 (antenna, voltage or current probe, etc.) and display device (CRO, strip chart recorder, etc.), unless it can be shown that the bandwidth of these devices will not restrict the bandwidth of the remainder of the detection system.
_________________
2 The bandwidth of some transducers (e.g., antennas, current probes) is very difficult or impractical to measure. In these cases, bandwidth measurements need not be made ou the device, but precautions shall be taken to assure that lhe device does not limit the overall detection system bandwidth.
F.5. (U) Impulse Bandwidth Measurements (IBW): Tunable Heterodyne Detection System with Demodulator. -- The impulse bandwidth of these detection systems shall be measured as follows:
a. (U) Apply the output of a calibrated AM sine wave generator to the input of the detection system. The generator output signal shall be amplitude-modulated 30 percent with a sine wave of suitable freauency.b. (U) Adjust the carrier frequency of the AM sine wave generator around the center frequency of the detection system until the maximum output level of the detected signal is observed at the same output port of the detection system used during TEMPEST testing. Note the output peak-to-peak amplitude observed on the oscilloscope and the signal level in rms volts of the AM sine wave applied at the input of the detection system.
c. (U) Disconnect the AM sine wave generator and apply the output of a calibrated impulse generator to the input of the detection system. Set the IG repetition rate to any convenient rate less than one-fifth of the nominal overall detection system bandwidth.
d. (U) Adjust the IG output level so that the peak magnitude of the waveform displayed on the oscilloscope (at the detection system output) is equal to one-half the peak-to-peak amplitude of the detected sine wave recorded in b (above). Note the level in volts (equivalent rms sine wave)/MHz of the impulsive signal applied at the input of the detection system.
e. (U) Calculate the impulse bandwidth of the detection system with the following formula:
0.3 (AM sine wave input signal level in rms volts recorded in b (above).)
IBW = __________________________________________________________________
(impulsive input signal level in volts (equivalent rms sine wave)/MHz, recorded in d (above).)
f. (U) Repeat the impulse bandwidth measurements at a minimum of two tuned frequencies per decade or one per tuning band (near the center), whichever is the greater number of readings.
F.6. (U) Impulse Bandwidth Measurements: Tunable Heterodyne or Tunable Non-Heterodyne Detection System Without Demodulator. -- The impulse bandwidth of these detection systems shall be measured as follows:
a. (U) Apply the output of a calibrated unmodulated sine wave generator to the input of the detection system.b. (U) Adjust the carrier frequency of the cw generator around the center frequency of the detection system until the maximum output level of the detection system is observed on an oscilloscope at the same port used during TEMPEST testing. Note the output peak-to-peak amplitude observed on the oscilloscope. and the signal level in rms volts of the cw sine wave applied at the input of the detection system.
c. (U) Disconnect the cw generator and apply the output of a calibrated impulse generator to the input of the detection system. Set the IG repetition rate to any convenient rate less than one-fifth of the nominal overall detection system bandwidth.
d (U) Adjust the IG output level so that the peak-to-peak waveform displayed on the oscilloscope (at the output of the detection system) is equal to the peak-to-peak amplitude of the cw waveform recorded in b (above). Note the level (in volts (equivalent rms sine wave)/MHz) of the impulsive signal applied at the input of the detection system.
e. (U) Calculate the impulse bandwidth of the detection system with the following formula:
(Sine wave input signal level in rms volts recorded in b (above).)
IBW = __________________________________________________________________
(impulsive input signal level in volts (equivalent rms sine wave)/MHz, recorded in d (above).)
f. (U) Repeat the impulse bandwidth measurements at a minimum of two tuned frequencies per decade or one per tuning band (near the center), whichever is the greater number of readings.
F.7. (U) Impulse Bandwidth Measurements: Non-Tunable Detection Systems. -- The impulse bandwidth shall be measured as follows:
a. (U) Apply the output of a calibrated unmodulated sine wave generator to the input of the detection system.
b. (U) Adjust the carrier frequency of the cw generator around the center frequency of the detection system passband.
c (U) Obtain a convenient display of the detection system output signal on an oscilloscope. Note the output peak-to-peak arnplitude observed on the oscilloscope and the signal level in rms volts of the cw sine wave applied at the input of the detection system.
d. (U) Disconnect the cw generator and apply the output of a calibrated impulse generator to the input of the detection system. Set the IG repetition rate to any convenient rate less than one-fifth of the nominal overall detection system bandwidth.
e. (U) Adjust the IG output level so that the peak magnitude of the waveform displayed on the oscilloscope (at the output of the detection system) is equal to one-half the peak-to-peak amplitude of the cw waveforrn recorded in c above. Note the level, in volts (equivalent rms sine wave)/MHz, of the impulsive signal applied at the input of the detection system.
g. (U) Calculate the impulse bandwidth of the detection system with the following formula:
(Sine wave input signal level in rms volts, recorded in c (above).) |
||
| IBW | = | __________________________________________________________________ |
(impulsive input signal level in volts (equivalent rms sine wave)/MHz, recorded in d (above).) |
UNCLASSIFIED
[Pages G-1 to G-12]
CONFIDENTIAL
[Full page of two boxes redacted.]
[Full page of two boxes redacted.]
[Half page with one box redacted.]
Note: See Table G-6 for application examples [Note to unknown table.]
[Full page with one box redacted.]
_________________
1 Lowest bit rate as defined in paragraph 3.1.42 Refer to Table G-5. [Footnotes to unknown figures.]
[Figure redacted.]
Figure G-1. -- Assumed Transition Time Based on Pulse Width Signaling
Rate (Maximum) (U)
[Figure redacted.]
Figure G-2. -- Bounds on Tunable Overall Detection System Bandwidth
(U)
[Figure redacted.]
Figure G-3. -- Maximum Permissible Tunable Starting Test Frequency (U)
Note: This figure is equivalent to Figure 10-1.
UNCLASSIFIED
Figure G-4. -- Typical Test Instrumentation for ER Tests (U)
Note: This figure is equivalent to Figure 10-2.
UNCLASSIFIED
Figure G-5. -- Required Minimum Antenna Distances From Metal Surfaces
and Objects Other Than the EUT (U)
[Page G-12 - Full page redacted.]
CONFIDENTIAL
[Pages H-1 to H-18]
UNCLASSIFIED
[All pages redacted.]
UNCLASSIFIED
[Pages I-1 to I-8]
UNCLASSIFIED
[All pages redacted.]
UNCLASSIFIED
[Pages J-1 to J-4]
UNCLASSIFIED
[All pages redacted.]
UNCLASSIFIED
[Pages K-1 to K-2]
UNCLASSIFIED
K.1. (U) Procedure. -- Impulse generators shall be calibrated by one of the four following methods:1
___________________
1 Other methods may be used if justified and approved by the sponsoring organization.
K.1.1 (U) Method 1.
a. (U) Apply the output of the impulse generator to be calibrated to the input of an amplitude-linear receiver having synchronously tuned, less-than critically-coupled, circuits. Radio interference field intensity receivers are satisfactory for this purpose if their impulse bandwidth is`at least five times the repetition rate of the impulse generator. Any automatic gain control (AGC) system shall be defeated. Once the receiver controls are set, they should not be changed during the calibration process.b. (U) Obtain an oscilloscope pattern of the overall receiver response at the IF output. The oscilloscope controls shall be so adjusted that the pattern is as large as possible within the calibrated area on the face plate. Either photograph or trace the pattern. Record the oscilloscope sweep speed setting. (The sweep speed shall be calibrated accurately.)
c. (U) Use a planimeter or other integrating device to determine the area of the positive portion of the major lobe of the response waveform. (More accuracy can be obtained by summing the area under the odd-numbered lobes and subtracting from it the total area under the even-numbered lobes.) This operation shall be carried out at least five times and the average of the readings taken as the area.
d. (U) Calculate the impulse bandwidth of the receiver in accordance with the following formula:
pattern height* in cm
IBW in MHz = _____________________________________
X 10-6
(pattern area* in cm2 (sweep speed in sec/cm)
*Refers only to positive portion of response waveform.
e. (U) Connect a calibrated sine wave generator to the receiver. Tune the generator to the receiver's tuned frequency and adjust the output until the peak pattern height is the same as that obtained with the impulse generator in a. and b. (above). Record the output of the sine v;ave generator in microvolts (rms).
f. (U) Calculate 20log10(e/d) where e and d are the results obtained in e. and d. (above) expressed in microvolts (rms) and megahertz, respectively. This calculation gives the spectral intensity of the impulse generator output in dB,µV/MHz (equivalent rms sine wave).
K.1.2 (U) Method 2.
a. (U) Select a bandpass or low-pass filter with the following characteristics:(1) (U) Minimum upper roll-off of 18 dB/octave.(2) (U) Maximum upper 3 dB cutoff point which is 10% of the reciprocal of the expected width of the driving impulse (from the IG to be calibrated) or 80% of the bandpass of the CRO in use, whichever is less.
(3) (U) Passband wide enough to permit passage of sufficient energy such that the peak voltage of the output waveform can be accurately read on the CRO.
(4) (U) 50 ohm input and output impedance in the passband.
b. (U) Determine thc impulse bandwidth (IBW) of the filter empioying the procedures specified in method 1, paragraphs a. through d. (above), substituting the word "filter" for "receiver". Once the IBW of the filter has becn measured, the filter may be used to calibrate any number of IGs; however, the IBW shall be rechecked in accordance with the calibration requirements specified in Paragraph 7.6.
c. (U) Terrninate the output of the IG to be calibrated with a 6 dB (minimum), 50 ohm pad and connect it to the input of the filter.
d. (U) Terminate the output of the filter with a 50 ohm resistive load and connect it to the vertical input of the CRO.
e. (U) Record the peak voltage of the filter output on the CRO microvolts.
f. (U) Calculate:
20log10(e/b) + pad loss - 3 dB + filter insertion loss
where e and b are the results obtained in paragraphs e. and b. (above), expressed in microvolts (peak) and megahertz respectively. This calculation gives the spectral intensity of the impulse generator output in dB,µV/MHz (equivalent rms sine wave).
K.1.3 (U) Method 3. -- Compare the output of the IG to be calibrated, with the output of another IG which has previously been calibrated, in accordance with method 1 or method 2, within the last six months.
K.1.4 (U) Method 4.
a. (U) Apply the output of the impulse generator to be calibrated to the input of a spectrum analyzer having the following characterstics:
(1) (U) Known impulse bandwidths.(2) (U) Absolute amplitude accuracy equal to +/-2 dB or better.
b. (U) Select a spectrum analyzer bandwidth at least five times the repetiton rate of the impulse generator, but no larger than one-tenth the usable spectrum of the impulse generator. Select a scan time in seconds/division, no less than 10/repetition rate (Hz) to insure ten-impulse responses per division.
c. (U) Add any conversion factors to the spectrum analyzer displayed voltage
needed to convert dBm to dB ref. 1 µV rms. Subtract the impulse
bandwidth of the spectrum analyzer in dB ref. 1 MHz from this value to convert
to dB ref. 1 µV/MHz and subtract 3 dB to convert the reading
to dBµV/MHz (equivalent rms sine wave), which is the spectral
intensity of the impulse generator output.
UNCLASSIFIED
[Pages L-1 to L-10]
UNCLASSIFIED
TEMPEST TEST PLAN OUTLINE
[Page L-2] THIS PAGE IS INTENTIONALLY BLANK
SAMPLE TABLE OF CONTENTS
Abstract
1 .0 Introduction
2.0 Equipment Under Test
2.1. Description of EUT
2.2. Theory of Operation
2.2.1, 2.2.2, 2.2.3, etc: Function of Each Box, as required
2.3. Operating Modes
3.0 RED Signals
3.1. RED Signal Description
3.2. RED Signal Flow diagram
4.0 RED and Black I/O Lines
5.0 Potential Carriers
6.0 TEMPEST Test Requirements
6.1. Test Procedures
6.2. Documentation
6.3. Test Media
6.4. RED Signals and Test Categories
6.5. Frequency Ranges
6.6. Bandwidth/Bandpass Selections
6.7. Exercise Equipment and Modes of Operation
6.8. Test Set-Ups
6.9. Monitor Signals
6.10. Test Messages
6.11. Predicted Detected Output Signals
6.12. Test Matrix
7.0 Test Capabilities
7.1. Test Facilities
7. 2. Instrumentation
7.3. Personnel Qualifications
Figures
2-1. Functional Block Diagram
2-2. System Block Diagram
2-3., etc. Additional Block Diagrams, if required
3-1. Time-Sequence RED Signal Flow Diagram, Simplified
4-1. Input/Output Lines
6-1. Exercise Equipment, Diagram
6-2. Synchronize/Monitor Test Points
6-3. Predicted/Detected Output Signal Displays
6-4. Documentation, examples
6-5. Test Setup
6-6., 6-7., etc: Other Test Setups, if required
7-1. Shielded Enclosure(s)
7-2. Certification: Test Facility
7-3. Certification: Instrumentation
Tables
6-1.-Test Matrix
7- 1. Instrumentation
[Page L-4] THIS PAGE IS INTENTIONALLY BLANK
OUTLINE DESCRIPTION (U)
Abstract (150 to 300 words)
1.0 (U) Introduction.
1.1. (U) Introductory statement, including exact identification of EUT: name and type number; purpose of test; contractual and subcontract information, if any; brief statement of configuration or modes of operation selected for testing and for certification, if applicable; any other statements necessary to round out the introduction for the reviewer, as well as for the technician who will be following this test plan and performing the actual TEMPEST test.1.2. (U) Include a list of all applicable documents such as NSTISSAM TEMPEST/1-91.
1.3. (U) Provide details of any waivers or exceptions, and justify.
2.0 (U) Equipment under Test. -- This section of the test plan describes the EUT in precise and definitive terms.
2.1. (U) Description of tbe EUT. -- This should include nomenclature, description of intended uses including actual applications as a system, as part of a system, or as a stand-alone, modes of operation, modes to be tested, power, I/O lines, etc.
2.2. (U) Theory of Operation. -- This should be in sufficient detail or depth to provide the U.S. Government reviewer and the person performing the TEMPEST tests with the knowledge to ascertain whether the test plan exploits all TEMPEST modes and conditions. Identify control and timing signals that are associated with processing of RED data.
(Figure 2-1. -- Functional Block Diagram)(Figure 2-2. -- System Block Diagram if applicable, to identify or clarify the position of the EUT in an operational system.)
2.2.1 (U) Function. -- If the device or system eonsists of more than one box, separate paragraphs may be used to describe the functions of each (2.2.2, 2.2.3, etc.). Use either a separate block diagram for each box or a consolidated single diagram.
2.3. (U) Operating Modes. -- Describe each mode of operation, e.g., manual, automatic, single channel, TDM, orderwire, ete.
3.0 (U) RED Signals. -- In this section, identify each EUT RED signal type, the major internal and external RED signal sources (S1, S2, S3, etc.) for each RED signal type, and all RED signaling rates (Rd1, Rd2, Rd3, Rt1, Rt2, Rt3, etc.). lt shall be considered a different RED signal type if there is a change in format, code, timing, transfer method, or parity. Determine the applicable test categories for each Rd and Rt. A time-sequence description and illustration of the RED signal flow shall be provided to properly identify all RED signal sources.
3.1. (U) RED Signal Description.
This section should present signal description in tabular form, including:
3.2. (U) RED Signal Flow Diagram. -- Figure L-1 presents an example of a time-sequence RED signal flow diagram. It is recommended that each RED signal be identified with consecutive mgmbers or letters, and that the same identification be used throughout the test plan and test report.
4.0 (U) RED and BLACK I/O Lines. -- This section enumertes all lines that connect to the EUT. Identify each RED line and each BLACK line that enters or leaves the EUT or the EUT area. Select and justify specific lines to be tested. Justify rejection of lines not to be tested. This should include signal lines, control lines, clocks, grounds, status lines, and others. (Figure 4-1. -- Input/Output Lines -- This should be a block diagram that differs from the functional block diagram of Figure 2-1 since it permits each line that interconnects EUT boxes or enters/leaves the EUT area to be shown and identified. Identification of each line should be clear and complete, including information on function, time, format, level, destination, and any other pertinent features.)
5.0 (U) Potential Carriers. -- Identify potential inadvertent carriers of RED information including possible areas where contamination with RED information may occur. An example could be clock harmonics, or any clock multiples or submultiples that provide timing informnation to more than one circuit or function. The TEMPEST test plan should point the way to search and verification by its thoroughness in listing all such potential carriers.
6.0 (U) TEMPEST Test Requirements. -- This section should include all details of the planned TEMPEST test, except for preliminary information in the preceding sections. The use of tables, as applicable, will be fully acceptable, with accompanying explanations as needed.
6.1. (U) Test Procedures. -- Provide a narrative description of both general and specific test procedures. Describe in general the procedures for running the tests and the process of operating the detection system to acquire and measure emanations. Include specific operation of the EUT and exerciser. The procedures for running the tests should be presented in the form of a specific guide for the TEMPEST test technician, including necessary adjustments for each operational mode to be explored. Include herein any special conditions to be observed and any specific software requirements to attain desired operational characteristics.
Figure L-1. -- Example of Test Plan Time-Sequence RED Signal Flow diagram,
Simplified (U)
6.2. (U) Documentation. -- Describe herein accessory equipment used for documentation, such as camera, chart recorder, etc. Include examples of data sheets used for manual recording of raw data for each test and for correcting, adjusting, and normalizing results. Attach examples of type/s of data sheets to be used. (Figure 6-4. -- Example(s) of Documentation Forms)
6.3. (U) Test Media. -- List the various media in which tests are to be performed including ER, MR, PLC, etc. (as well as tunable and non-tunable). Include each signal line, control line, clock line, powerline, exc., to be tested. Exceptions, deletions, limitations, or modifications will require rationale and authority from the sponsoring organization for each change.
6.4. (U) RED Signals and Test Categories. -- From the RED signal sources identified in Paragraph 3.0, select those RED signals/sources to be investigated as part of this TEMPEST test. Justify those not selected for testing. Select the appropriate test category for each RED signal source.
6.5. (U) Frequency Ranges. -- Include a narrative justifying selection of appropriate frequency ranges for both tunable and non-tunable tests.
6.6. (U) Bandwidth/Bandpass Selections. -- Explain selections of bandwidths and bandpasses for tunable and non-tunable tests. State the bandwidth limitations, if any, of the instrumentation.
6.7. (U) Exercise Equipmeut and Modes of Operation. -- Describe the equipment and system to be used to exercise the EUT. Present the rationale for selection of this equipment and this test system. Include explanation why certain modes, if any, were selected for test exercise and why other modes of operation, if any, were excluded from such testing. Describe the physical location of the exercise equipment. Describe use of any special operating techniques, e.g., use of software to exercise certain portions of the EUT.
(Figure 6-1.-Exercise Equipment, Diagram)
6.8. (U) Test Setups.
6.8.1 (U) Clearly describe and diagram the test setup(s) to be used for text media examinations (ER, MR, BLC, PLC, and RLC). Generally, only one dlagram will be needed; however, additional diagrams rnay be necessary for clarity. Include the test environment or shielded test enclosure, EUT, auxilary equipment, exercise equipment, power supplies, blocks, detection and measurement equipment, oscilloscopes, PLISN's, filters, EUT ground planes, grounds, etc. Specify EUT grounding methods for both signal and safety. Also, specify how the cabinet is connected in the grounding scheme. The description and diagram should make clear what is to be in the test enclosure(s), what is to be placed in any auxiliary shielded enclosure(s), and what is to be placed or used outside shielded enclosures. Provide justification if the type and installation of conduits and cables used in the EUT test setup are not the same as those specified for the actual operational installation.6.8.2 (U) If the equipment or system can or may be operated in more than one mode or more than one configuration, list and describe all such variations. If applicable, explain why certain modes are selected and why others are not to be tested. This explanation should tie in with the intent of this test and thus with the EUT description in Paragraphs 1.0 and 2.1 of this test plan. Accordingly, TEMPEST accreditation, as a result of the test to be performed, will not include the equipment or system in the modes or configurations excluded in this test plan, unless due justification is provided herein.
(Figure 6-5, and, if required, 6-6, 6-7, etc.: Test Setup)
6.9. (U) Monitor Signals. -- Explain and diagram specifically how and where monitor and/or synchronization signals are to be derived for the purpose of comparing or correlating detected emanations with RED signals in Paragraph 3.0 of this test plan. Describe what precautions will be taken to preclude signal distortions and false indications of detected emanations.
(Figure 6-2. -- Synchronize/Monitor Test Points)
6.10. (U) Test Messages.
6.10.1 (U) Select test messages, words, characters, or input states which will succeed in running the EUT through all combinations of conditions representative of all operational usages. Test messages should also be selected or designed to aid in rapid correlation of detected ernanations by assuring a high degree of recognition or identification.6.10.2 (U) Present in this section all the actual test messages to be used for testing, and include rationale for selections made.
6.11. (U) Predicted Detected Output Signals. -- Include explanation of hypothetical detected compromising ernanations. These should relate directly to the test messages described in Paragraph 6.10 above.
(Figure 6-3. -- Predicted Detected Output Signals)
6.12. (U) Test Matrix. -- This section should gather together in a single table, as a ready reference, all information required to perform all TEMPEST tests.
(Table 6-1: Test Matrix. See example in Table L-1).
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
7.0 (U) Test Capabilities. -- This is the section for reporting on facilities to be employed in the projected TEMPEST testing, if not covered in a separate facilities certification report.
7.1. (U) Test Facilities.
7.1.1 (U) Describe facilities to be used in the planned test, including dimensions, type of construction, shielding materials, panel seam scheme, attenuation, door(s), lighting, air-conditioning, air ducts, powerline filtering, power entrance, signal entrance scheme, grounding details, use of companion room(s) for test equipment and/or exercise equipment.(Figure 7-1.-Shielded Enclosure(s))7.1.2 (U) If not covered in a separate certification report, include herein as Figure 7-2, certification attesting to test facility in accordance with Paragraph 6.5 of this document.
7.2. (U) Instrumentation.
7.2.l (U) Describe measurement cquipment, including detection cquipment, antennas, attenuators, oscilloscopes, power supplies, filters, PLISN's, signal generators, IG's, probes, etc., if not covered in a separate detection system certification report.(Table 7-l: Instrumentation)7.2.2 (U) Include manufacturer, type number, description, frequency range, categories covered, bandwidths, etc., as applicable.
7.2.3 (U) If not covered in a separate certification report, include herein, as Figure 7-3, detailed certification attesting to last calibration of frequencies, sensitivity, etc., in accordance with Paragraph 6.4 of this document.
7.3. (U) Personnel Qualifications. -- Provide qualifications of
supervisory and tcchnical personnel who prepared this test plan, as well
as those who will perform the tests and those who will write thc TEMPEST
evaluation report.
UNCLASSIFIED
[Pages M-1 to M-3]
UNCLASSIFIED
| ACCESSION NUMBER | Leave blank, number assigned by the NTIC. |
| CLASSIFICATION | Fill in classification of profile. |
| ORIGINATING SERVICE OR AGENCY |
Fill in the name and address of service or agency that is paying for the test or originated test tasking. |
| ORIGINATOR'S ID NO./ PROJECT NO. |
Number assigned by testing organization to this project. Enter task number or report number. |
| CONTRACT NUMBER | Enter contract number if applicable. |
| TYPE | Enter X in the appropriate line: Lab, Fielded, or Study. |
| TESTING ORGANIZATION | Enter name and address of testing organization. |
| TEST STANDARD | Enter test standard(s) applicable to equipment. |
| DATES OF TEST | Enter dates equipment was under test (from - to). |
| REPORT T1TLE | Enter official title of report as it appears on the front cover. |
| REPORT DATE | Enter date of the report as it appears on the front cover. |
| DISTRIBUTION CODE | Enter X in the appropriate line. If report is limited, and cannot be released to the entire TAG Community, attach explanation. |
| ABSTRACT | Brief description of the report. |
| OBJECTIVES | Enter X in the appropriate line. |
| EUT DESCRIPTION | Brief description of equipment under test; to include:
MODEL NUMBER Enter model number. MANUFACTURER (no abbreviations) EQUIPMENT NAME Enter other names equipment is known by (e.g., LaserJet Series III, SPARCStation, SCOPE etc., do not enter the model number here). EQUIPMENT CATEGORY (see NTIC's TEMPEST Zone Assignments publication. EQUIPMENT COMMENTS List any options or equipment tested with the equipment (e.g., tested with a Zenith ZCM-1492 monitor). |
| RESULTS | Enter NSTISSAM TEMPEST Level and enter X in the appropriate compliant
box.
Enter Zone Rating as: A-D, B-D, C-D, or D Enter Walk-Away Distance (if applicable). Enter Comments about the Results. |
|
|||||
| Originating Service or Agency |
Orig. ID No./Project No. |
Type
Laboratory _________ |
|||
| Contract No. | |||||
| Testing Organization |
Test Standard |
Dates of Test |
|||
| Report Title |
Report Date |
Dist. Code All TAG _________ Limitred _________ |
|||
ABSTRACT |
|||||
OBJECTIVES |
|||||
| NSTISSAM TEMPEST/1-92 Compliance Evaluation______________ TEMPEST Zone Evaluation__________________________________ |
|||||
EUT DESCRIPTION |
|||||
| Model No. _________________ Manufacturer
_________________ Equipment Name __________________________________________ Equipment Category _______________________________________ Equipment Comments: |
|||||
RESULTS |
|||||
| NSTISSAM TEMPEST Level ________ Compliant: Yes ___ No:
___
Zone Rating: __________ Walk-Away Distance: __________
Result Comments: |
|||||
[Form]
UNCLASSIFIED
(when blank)
_________________
CLASSIFICATION
COMMENT FORM
for
Use one form per comment,
Return completed form to:
Director
National Security Asency
ATTN: C9
Fort George G. Meade, Maryland 20755-6000
1. Date:
2 Name of Contributor:
3. Name of Organization:
4 Address of Organization:
5. Reference section in document (paragraph. page number, line number if
required; if general comment describe subject to be discussed):
6. Comment (What should be changed?):
7. Alternative (What should it be changed to?):
8. Rationale (why should change be made?):
If more space is required for any of the above items, use extra sheet(s)
and attach to this form.
UNCLASSIFIED
(when blank)
[Rear Cover]
[Two pages] Distribution List (Separate file)
End of document.
Transcription and HTML by Cryptome.
